Parallel Jaw Grip 4601 Series with Hot Latch/Sprig
KT4601
- Versatile grip hold a wider range of ACSR cable sizes reducing the number of grips needed
- Round jaw holds 0.30 to 0.80-Inch (7.62 to 20.30 mm) diameter cable range
- Large opening in the handle accommodate a wide variety of hooks on hoists, winches and tackle blocks
- Locking handle keeps jaw open while grip is placed on cable with a hot stick
- Hot latch closes automatically to guard wire
- Max Safe Load of 10,000-Pound (4536 kg)
带有热闩锁/小枝的平行钳夹具4601系列
KT4601
- 多功能手柄可容纳更广泛的ACSR电缆尺寸,减少了所需的夹具数量
- 圆形钳口可容纳0.30至0.80英寸(7.62至20.30 mm)直径的电缆
- 手柄上的大开口可容纳起重机,绞车和滑车组件上的各种挂钩
- 锁定手柄保持钳口打开,同时用热棒将电缆夹在电缆上
- 热闩锁自动关闭以保护电线
- 最大安全载荷10,000磅(4536千克)
Klein Tools has been manufacturing high quality grips for more than 135 years. Klein Parallel Jaw Grips are lightweight and compact. They can pull an exceptionally wide range of cable types and sizes.
Specifications
Type:
Parallel Jaw Grip
Application:
Wide Variety of Hooks on Hoists, Winches and Tackle Blocks
Special Features:
Hot Latch, Spring, Locking Handle
Overall Length:
10” (254.0 mm)
Overall Height:
1” (25.4 mm)
Overall Width:
8” (203.2 mm)
Cable Type:
ACSR
Cable Diameter:
0.30” to 0.80” (7.62 to 20.3 mm)
Jaw Type:
Round – Serrated
Jaw Length:
5” (127.0 mm)
Maximum Safe Load:
10,000 lb (4536 kg)
Weight:
7.0 lb (3.2 kg)
UPC:
092644477546
WARNINGS
- Before each use, clean jaw area and inspect grip for proper operation to avoid slippage.
- When used on/near energized lines, ground, insulate, or isolate grip before pulling.
- Do not exceed rated capacity.
- Always match proper size and type of grip to application.
- Grips are to be used for temporary installation, not for permanent anchorage.
Klein Parallel Jaw Grips轻巧紧凑。它们可以提供种类繁多的电缆类型和尺寸。
产品规格
类型:
平行钳夹
应用:
葫芦,绞车和滑车组上各种各样的挂钩
特殊功能:
热门闩,弹簧,锁定手柄
总长度:
10”(254.0 mm)
总体高度:
1”(25.4 mm)
总宽度:
8”(203.2 mm)
电缆类型:
钢芯铝绞线
电缆直径:
0.30”到0.80”(7.62到20.3 mm)
颚类型:
圆形 – 锯齿形
下颚长度:
5”(127.0 mm)
最大安全载荷:
10,000磅(4536千克)
重量:
7.0磅(3.2千克)
UPC:
092644477546
警告
- 每次使用前,清洁钳口区域并检查手柄是否正确操作以避免滑动。
- 在拉动时在通电线上/附近使用,接地,绝缘或隔离手柄。
- 不要超过额定容量。
- 始终将适当尺寸和类型的手柄与应用相匹配。
- 把手用于临时安装,而不是用于永久性锚固。