Parallel Jaw Grip 4600 Series
KT4600
- Versatile grip hold a wider range of ACSR cable sizes reducing the number of grips needed
- Round jaw holds 0.30 to 0.80-Inch (7.62 to 20.30 mm) diameter cable range
- Large opening in the handle accommodate a wide variety of hooks on hoists, winches and tackle blocks
- Max Safe Load of 10,000-Pound (4536 kg)
平行钳夹4600系列
KT4600
- 多功能手柄可容纳更广泛的ACSR电缆尺寸，减少了所需的夹具数量
- 圆形钳口可容纳0.30至0.80英寸（7.62至20.30 mm）直径的电缆
- 手柄上的大开口可容纳起重机，绞车和滑车组件上的各种挂钩
- 最大安全载荷10,000磅（4536千克）
Lightweight, compact grips pull an exceptionally wide range of cable sizes and types. Designed with a round serrated jaw to firmly grip insulated cables and conductors. A hot latch closed automatically to guard against grip accidently disengaging from wire. A large opening in the handle accommodates a wide variety of hooks on hoists, winches and tackle blocks.
Specifications
Type:
Parallel Jaw Grip
Application:
Firmly Grip Insulated Cables and Conductors
Special Features:
Spring
Overall Length:
13” (330.2 mm)
Overall Height:
1.5” (38.1 mm)
Overall Width:
5” (127.0 mm)
Cable Type:
ACSR
Cable Diameter:
0.30” to 0.80” (7.62 to 20.3 mm)
Jaw Type:
Round – Serrated
Jaw Length:
5” (127.0 mm)
Maximum Safe Load:
10,000 lb (4536 kg)
Weight:
7.0 lb (3.2 kg)
UPC:
092644477539
WARNINGS
- Before each use, clean jaw area and inspect grip for proper operation to avoid slippage.
- When used on/near energized lines, ground, insulate, or isolate grip before pulling.
- Do not exceed rated capacity.
- Always match proper size and type of grip to application.
- Grips are to be used for temporary installation, not for permanent anchorage.
轻巧紧凑的手柄可以拉伸各种尺寸和类型的电缆。采用圆锯齿钳口设计，牢固地夹住绝缘电缆和导线。热闩锁自动关闭以防止意外脱离导线的夹持。手柄上有一个大开口，可容纳升降机，绞车和滑车组件上的各种钩子。
产品规格
类型：
平行钳夹
应用：
坚固的绝缘电缆和导体
特殊功能：
弹簧
总长度：
13”（330.2 mm）
总体高度：
1.5英寸（38.1毫米）
总宽度：
5”（127.0 mm）
电缆类型：
钢芯铝绞线
电缆直径：
0.30”到0.80”（7.62到20.3 mm）
颚类型：
圆形 – 锯齿形
下颚长度：
5”（127.0 mm）
最大安全载荷：
10,000磅（4536千克）
重量：
7.0磅（3.2千克）
UPC：
092644477539
警告
- 每次使用前，清洁钳口区域并检查手柄是否正确操作以避免滑动。
- 在拉动时在通电线上/附近使用，接地，绝缘或隔离手柄。
- 不要超过额定容量。
- 始终将适当尺寸和类型的手柄与应用相匹配。
- 把手用于临时安装，而不是用于永久性锚固。
