Chicago? Grip for EHS Cable, Curved Jaw

1684-74

  • When pulling EHS (extra-high-strength) galvanized-steel cable, the galvanizing has a tendency to coat the jaws of any grip, causing the cable to slip
  • To reduce the possibility of slippage and damage to the cable, the jaws of this grip are milled on a curve with a double ”V” contour

用于EHS电缆的Chicago 握把，弯曲的钳口

1684-74

  • 当拉EHS（特别高强度）镀锌钢电缆时，镀锌会有夹钳的钳口涂层，导致电缆滑动
  • 为了减少滑动和损坏电缆的可能性，该手柄的钳口铣削成具有双“V”轮廓的曲线

Designed for use on aluminum, copper, weatherproof coated wire, PVC covered conductors and messenger and guy strand. The Chicago style grip was designed for cable sizes from 0.12-Inch to 1.0-Inch (3.10 to 25.4 mm). When pulling EHS (extra-high-strength) galvanized-steel cable, the galvanizing has a tendency to coat the jaws of any grip, causing the cable to slip. Double -InchV-Inch contour reduces the possibility of slippage and damage to the cable.

Specifications
Cable Type:
Aircraft, EHS, Messenger, Guy Strand
Cable Diameter:
0.218” to 0.55” (5.54 to 13.97 mm)
Jaw Type:
Double V, Milled Curved
Jaw Length:
5” (127.0 mm)
Maximum Safe Load:
8000 lb (3629 kg) EHS Specific
Weight:
5.6 lb (2.6 kg)
UPC:
092644471728
WARNINGS
  • Before each use, clean jaw area and inspect grip for proper operation to avoid slippage.
  • When used on/near energized lines, ground, insulate, or isolate grip before pulling.
  • Do not exceed rated capacity.
  • Always match proper size and type of grip to application.
  • Grips are to be used for temporary installation, not for permanent anchorage.

设计用于铝，铜，防风雨涂层电线，PVC覆盖导体和信使和绞线。芝加哥式握把设计用于0.12英寸至1.0英寸（3.10至25.4毫米）的电缆尺寸。当拉动EHS（特别高强度）镀锌钢电缆时，镀锌倾向于涂覆夹具的钳口，导致电缆滑动。双-InchV-Inch轮廓减少了滑动和损坏电缆的可能性。

产品规格
电缆类型：
飞机，EHS，信使，Guy Strand
电缆直径：
0.218英寸至0.55英寸（5.54至13.97毫米）
颚类型：
双V，铣削曲面
下颚长度：
5”（127.0 mm）
安全载荷：
8000磅（3629千克）EHS特定
重量：
5.6磅（2.6千克）
UPC：
092644471728
警告
  • 每次使用前，清洁钳口区域并检查手柄是否正确操作以避免滑动。
  • 在拉动时在通电线上/附近使用，接地，绝缘或隔离手柄。
  • 不要超过额定容量。
  • 始终将适当尺寸和类型的手柄与应用相匹配。
  • 把手用于临时安装，而不是用于永久性锚固。